Reset Hitachi Air Conditioner Systems Safely at Home
Knowing how to reset Hitachi air conditioner systems properly can get a stalled airHome split back on its feet after a storm, a blackout or a confused handset.
A reset gives the boards a clean start, nothing more. It will not replace a worn fan motor or seal a leak. This guide shows the safe method, the difference between resetting the unit and resetting the handset, and when to stop trying.
What does a power cycle actually do?
Cutting power at the switchboard shuts down the indoor board, the outdoor board and the drive electronics. When power returns, each board starts from scratch, reads its stored settings, checks its sensors and re establishes communication with the other unit. Any confusion caused by a brief power disturbance is wiped away.
If the stop came from a real fault, the boards find it again and report the same pattern.
Why use the switchboard rather than the handset?
Pressing off on the handset only stops operation. The boards stay powered and keep their current state. A switchboard power cycle is the only way to give them a genuine fresh start. If your outdoor unit has its own isolator, switching that off too makes doubly sure.
How do you reset Hitachi air conditioner units step by step?
Follow this sequence.
- Press off on the handset and wait for the louvre to close.
- Switch the air conditioner circuit off at the switchboard.
- Wait at least five minutes.
- Switch the circuit back on.
- Wait a minute or two for the boards to start up.
- Press on with the handset and choose your mode.
Then give the system a full ten minutes to settle before judging the result either way.
Why wait five minutes?
Inverter boards hold stored charge in their capacitors for a while after power is cut. Waiting lets that charge drain so the restart is complete. It also lets refrigerant pressures settle, which makes the compressor start more easily.
When is a reset worth trying?
A reset makes sense after a storm, power cut or brownout, when the unit stops for the first time with a pattern you have not seen before, or when the handset and unit seem out of step. It is a reasonable first step for communication and memory patterns in particular.
When should you not keep resetting?
Avoid repeated resets for patterns involving current, voltage or the compressor, such as two, three, four, ten or fourteen flashes on the operation lamp. Each restart against those faults adds stress. One restart, then call us. Our code list explains each pattern.
Is there a reset button on the handset?
Hitachi handsets carry a small reset key, which the airHome service catalogue uses as part of a technician button sequence for reading error history. Pressing it alone typically resets the handset itself, not the indoor or outdoor boards. Your owner manual explains what it does on your model.
What about resetting the wifi module?
Hitachi manuals describe restoring factory settings for the built in wifi module and then confirming pairing mode by watching the wifi lamp blink three times after a power restart. That process affects only the wifi connection, not the air conditioner settings. Our wifi guide explains it.
What should you check before resetting?
Fresh handset batteries, the right mode and set point, no active timer, clean filters and a clear outdoor unit all rule out simple causes. A tripped breaker or switched off isolator can also look like a fault.
What happens after power returns?
The boards start up, the louvre may move to its home position and the unit may beep. In heating, the indoor fan waits until the coil warms, and the operation lamp may blink slowly during preheat. That is normal. In cooling, cold air usually follows within several minutes.
What if the pattern returns immediately?
Then the boards have found a real fault. Note the lamp and the number of flashes, switch off and book a technician. Our code reading guide explains how to count reliably.
What if the unit will not start at all?
Check that power has really returned at the switchboard and the isolator. Try fresh handset batteries. If the display stays dark, see our wont turn on guide.
Why do storms leave units confused?
During a storm, the supply can flicker, dip and spike several times within seconds. Each disturbance can interrupt the boards mid conversation, leaving them in an odd state. In addition, a surge can scramble the data the boards hold in working memory. Consequently, a unit may refuse to start or show a communication pattern after a storm even though nothing is damaged. A clean power cycle usually sorts that out.
However, if a surge has damaged a component, the pattern returns straight away, and a technician needs to test the boards.
Should you wait for the storm to pass?
Yes. Restarting during a storm risks another surge hitting the boards while they start up. Leave the system off at the switchboard until the storm has passed and power is stable, then follow the reset steps.
How does a blackout affect the settings?
After a full blackout, the handset keeps its own settings, but the indoor unit may need a fresh command to start. Some models resume automatically. Wifi connected units may take a few minutes to reconnect to the airCloud Go app. Timers set on the handset may also need setting again.
Our timer guide explains timers.
What about multi split systems?
A reset at the switchboard restarts the shared outdoor unit and every indoor head together. If only one head showed a pattern, note which room it was in. In addition, make sure every head is set to the same mode after the restart, since one outdoor unit cannot heat and cool at once.
Does a reset work for ducted systems?
The principle is the same. Ducted systems like the airCore 700 may have separate breakers for the indoor unit in the roof and the outdoor unit, so switch both off. Wired wall controllers can take a little longer to reconnect after power returns. Our ducted page covers ducted systems.
How often is too often?
An occasional reset after a storm is perfectly normal. Needing one every week, or several times a day, signals an underlying fault that is getting worse, such as a loose connection, a failing sensor or a refrigerant leak. Keep a short log of each stop, then book a check.
Can a reset damage anything?
A single careful reset is safe. Problems arise when owners switch the system off and on rapidly, which gives pressures no time to settle and can make the compressor start against high pressure. Repeatedly resetting a breaker that keeps tripping is also dangerous. Follow the five minute rule, and stop after one attempt if the same fault pattern returns.
What details should you note?
Write down the lamp and number of flashes before resetting, the time, the weather, and whether the reset helped. Those notes are valuable for the technician, especially if the fault comes and goes.
Is resetting covered by warranty?
Switching the system off and on at the switchboard is normal use and has no effect on cover. Hitachi lists a six year parts and labour warranty on its airHome wall mounted range in Australia. Opening panels or tampering with wiring is a different matter, so leave that to licensed technicians.
Where is the air conditioner breaker?
Most Sydney homes have a dedicated circuit for each split system at the main switchboard, often labelled AC, air con or with the room name. Some homes have a separate sub board in a garage or laundry. In addition, many outdoor units have a weatherproof isolator mounted on the wall beside them. If labels are missing, check which breaker turns the indoor display off, and warn the household before switching anything that might feed a fridge or computer.
What if the breaker has tripped?
A tripped breaker sits in the off or middle position. Switch it fully off, then on again once. If it trips again straight away, leave it off. Repeated tripping means an electrical fault, such as a short in the compressor, a damaged cable or water in the electrics, and needs a licensed technician.
Our turns off guide explains related symptoms.
What happens to the clean function lamp after a reset?
After power returns, the clean function lamp may behave differently for a while, since FrostWash timing restarts. If it later blinks four seconds on and one second off, Hitachi manuals describe that as a reminder that FrostWash has not run for a long time. It is not a fault.
Does the reset affect FrostWash or Mold Guard?
Not in any harmful way. Those functions resume their normal behaviour once the unit runs again. If you had FrostWash scheduled or set to run automatically, check the setting on the handset or app after a long outage.
How do you know the reset worked?
The unit starts normally, the indoor fan runs at the expected speed, the outdoor unit starts within a few minutes, and the air from the louvre turns cool or warm as expected. No fault pattern appears over the next hour or so. If all of that happens, the stop was likely a passing glitch.
When should you reset the handset instead?
If the handset display is frozen, shows strange symbols or stops sending commands after a battery change, the handset itself may need a reset. Removing the batteries for a minute and refitting them often helps. Our remote guide explains further handset checks.
Can heat waves cause stops that look like faults?
Yes. On extreme days, outdoor units in full sun with poor airflow can hit their load limits, and the board stops the compressor to protect it. Patterns such as five or sixteen flashes on the operation lamp are typical. A reset after the heat eases often works, but the real fix is better airflow, a clean coil and shade. Our guide to operation lamp 16 flashes explains high load stops.
What about frosty mornings?
In winter heating, the outdoor coil collects frost and the unit runs defrost cycles. During defrost, the indoor fan pauses, the operation lamp blinks slowly and steam may rise from the outdoor unit. Resetting during defrost only interrupts it. Wait ten minutes or so before deciding anything is wrong.
Should you reset before a technician visits?
If the system has stopped with a pattern, note the pattern first, then try one reset. Tell the technician what happened. If the reset cleared the fault, the stored error history may still show it, which helps diagnosis.
Is it safe to open the front cover after a reset?
Lifting the front cover to wash the filters is fine with the unit switched off. Anything beyond the filters, including the inside of the indoor unit and the whole outdoor unit, should stay closed. Licensed technicians handle anything behind panels.
What if someone else already reset it several times?
Tell us. Repeated resets can hide useful clues, and if the pattern involved current or the compressor, the technician will check those parts carefully for extra stress. The stored history may also show how many times the fault occurred, which helps judge whether the problem is getting worse over time or simply happened once after a storm.
When is it time to call us?
Call if the same pattern returns after one reset, the breaker trips, you smell burning or the unit makes grinding or banging noises.
Do we help across Sydney?
Yes. We repair Hitachi airHome systems throughout Greater Sydney. Ring 02 9071 1142 or use our contact page.
Frequently asked questions
How long should a Hitachi unit stay off for a reset?
At least five minutes at the switchboard.
Does the handset reset key reset the system?
Usually it resets the handset or forms part of a service sequence, not the boards.
Which patterns should not be reset repeatedly?
Current, voltage and compressor patterns on the operation lamp.
Will a reset clear a real fault?
No. The boards will find it again.
Is the slow blink after a restart normal?
Yes, in heating it shows preheat.
How do I book?
Ring 02 9071 1142 or use our contact page.