Hitachi Operation Lamp Blinking 6 Times, Compressor Overheat
The Hitachi operation lamp blinking 6 times means a temperature sensor on the hot side of the compressor has climbed past its safe limit.
Hitachi lists the pattern as an OH thermistor temperature rise, OH being short for overheat. The board stops the compressor before heat can damage it. Low refrigerant, poor airflow and restrictions in the circuit are the classic reasons a compressor runs too hot.
What is the OH thermistor?
The OH thermistor is a temperature sensor fixed to the hot side of the compressor circuit, typically on or near the discharge, where hot compressed refrigerant leaves the compressor. That spot is the hottest point in the system, so it gives the board an early warning when the compressor is working outside its comfort zone.
When the reading climbs too high, the board stops the compressor and reports six flashes.
What does Hitachi say?
The airHome service catalogue lists six flashes of the operation lamp as overheat thermistor temperature rise. Hitachi Australia also lists, in its professional tutorial material, a code meaning compressor discharge temperature too high, which describes the same kind of condition.
How do you confirm six flashes?
Count the flashes on the indoor operation lamp between pauses, over at least two cycles. The slow blink during preheat and defrost in heating is a different, normal pattern. Long press a handset arrow key to start the service buzzer if the lamp is hard to read.
What makes the Hitachi operation lamp blinking 6 times appear?
Typical causes include the following.
- Low refrigerant from a leak.
- A restriction such as a blocked strainer or kinked pipe.
- An expansion valve that is stuck nearly closed.
- A blocked outdoor coil or weak outdoor fan.
- Very high outdoor temperatures.
- A faulty OH thermistor giving a false high reading.
Why does low refrigerant make the compressor hot?
Refrigerant does two jobs for the compressor. It carries heat away, and returning cool gas helps keep the compressor body temperature down. With too little refrigerant, the gas returning to the compressor is warmer and thinner, so the compressor heats up. Discharge temperature climbs, and the OH thermistor sees it.
Our gas page explains leak repair.
How does a restriction cause overheating?
A partial blockage starves the compressor of returning refrigerant in much the same way as low gas. Kinked pipes, blocked strainers and a sticky expansion valve are common restrictions. Frost or ice at the point of restriction is a tell tale sign.
Can airflow be enough to cause it?
Yes, especially in cooling on hot days. A blocked outdoor coil, a slow outdoor fan or a unit breathing its own hot exhaust all raise pressures and temperatures. The compressor discharge gets hotter as a result.
Could the sensor be wrong?
Sometimes. A thermistor that has drifted or a connector that has corroded can read high when the compressor is actually fine. That is why the technician checks the real discharge temperature with a separate probe before blaming the refrigerant circuit.
What can you check yourself?
Make sure the outdoor unit has clear space and a clean coil, check the outdoor fan turns, and look for frost on the smaller pipe at the outdoor unit. Note whether cooling had been weakening before the pattern appeared. Keep the cabinet closed at all times.
Is a restart sensible?
One restart, after the compressor has had time to cool, is reasonable. Switch off at the switchboard for at least ten minutes, then restart. If six flashes return, leave the system off. Running an overheating compressor repeatedly shortens its life. Our reset guide has the steps.
How do we diagnose it?
The technician measures actual discharge temperature, refrigerant pressures, superheat and subcooling, checks the expansion valve, inspects the outdoor coil and fan, and tests the OH thermistor resistance. Those readings show whether the compressor really overheated and why.
What repairs are typical?
Leak repair with pressure testing, vacuum and recharge fixes low gas. Replacing a restricted component or kinked pipe fixes blockages. Cleaning the coil and repairing the fan fixes airflow. Replacing the thermistor fixes false readings.
How much does it cost?
A sensor or coil clean costs less than a leak repair or component replacement involving refrigerant work. Our pricing page explains what drives cost, and we quote first.
Which patterns are related?
One flash of the timer lamp is a refrigerant cycle fault. Five and sixteen flashes on the operation lamp relate to heavy load. Seven flashes relates to other outdoor thermistors. Our code list covers them.
Why does weak cooling often come first?
Overheating rarely appears out of nowhere. For example, a slow leak gradually reduces the charge over weeks or months. During that time, cooling weakens, the system runs longer and the compressor gets warmer each day. Eventually, on a hot afternoon, the discharge temperature crosses the limit and the board stops with six flashes. Consequently, owners often realise in hindsight that the room had not been cooling well for a while.
Therefore, if cooling has been fading, mention it when you book, since it strongly suggests a refrigerant problem.
How does superheat tell the story?
Superheat is the difference between the actual temperature of refrigerant gas returning to the compressor and the temperature at which it boils at that pressure. High superheat means the gas has picked up far more heat than normal, which usually points to low charge or a restriction. In turn, high superheat leads to high discharge temperature. Technicians measure it to understand why the compressor ran hot.
Can an expansion valve cause overheating?
Yes. The electronic expansion valve controls how much refrigerant enters the evaporating coil. If it sticks nearly closed, or if its coil or drive fails, too little refrigerant flows. As a result, the compressor is starved and runs hot, much as if the system were low on gas. The technician tests the valve coil and watches how pressures respond when the board commands the valve.
Is the problem worse in summer or winter?
In cooling, high outdoor temperatures add to the load, so overheating is most common in summer. However, in heating, a low charge or restriction can still cause high discharge temperatures, especially on cold mornings when the system works hard to warm the house. Therefore, six flashes can appear in either season.
What can you do while waiting?
Switch the system off at the switchboard if the pattern returns, and give the compressor time to cool. In summer, use fans, close blinds and keep to the coolest rooms. In winter, use safe portable heating. Above all, avoid restarting the system repeatedly, since each run pushes the compressor back into the danger zone.
How can you prevent the fault?
Book a yearly service that includes refrigerant pressure checks, so slow leaks are found early. In addition, keep the outdoor coil clean and the area around it open, protect pipe work from damage during renovations or garden work, and wash indoor filters regularly. Those habits reduce the main causes of overheating.
Does warranty cover it?
Hitachi lists a six year parts and labour warranty on its airHome wall mounted range in Australia. A leak or valve failure caused by a manufacturing defect may be covered. Damage from installation errors, renovation work, pests or neglect usually falls outside warranty terms.
What details help us prepare?
Please share the indoor model number, whether cooling or heating had been weakening, whether you saw frost on pipes, whether the system has been regassed before and where the outdoor unit sits. In addition, note the outdoor temperature when the pattern appeared.
Why do technicians weigh the refrigerant charge?
Each split system has a specific charge listed on its rating label, adjusted for pipe length. The most accurate way to restore it after a repair is to evacuate the system and weigh the correct amount back in. Guessing by pressure alone can leave a system short, which leads straight back to overheating, or overcharged, which causes other problems. Our technicians weigh the charge as standard practice.
Can a kinked pipe hide behind the unit?
Yes. The refrigerant pipes often bend sharply behind the indoor unit or where they enter the wall. If an installer bent them too tightly, or if someone later pushed the indoor unit against the wall, a kink can form out of sight. The technician looks for temperature drops or frost along the pipe run to find such restrictions.
What does a strainer do?
Many systems include small strainers or filter driers in the refrigerant circuit to catch debris and moisture. Over many years, or after a compressor failure, these can clog. A clogged strainer acts like a kink, starving the compressor. Replacing it involves recovering refrigerant and recharging afterwards.
How do we test the OH thermistor itself?
The technician measures the actual temperature at the sensor location with a calibrated probe, then compares it with the thermistor resistance and the value the board expects. If the real temperature is normal but the sensor reads high, the sensor or its wiring is at fault. That simple check prevents unnecessary refrigerant work and saves the owner money when the compressor is actually healthy.
Is it safe to touch the outdoor pipes?
Avoid it. In cooling, the larger pipe can be very cold and the discharge line inside the unit very hot. In heating, the roles reverse. Moreover, the outdoor unit contains moving parts and live terminals. Look, but do not touch, and leave all checks behind the cabinet to a technician.
Will we explain the readings?
Yes. After testing, the technician explains whether the compressor truly overheated, what the pressures and superheat showed and which part needs attention. Once the repair is complete, they show you that discharge temperature and pressures have returned to normal.
How long does a repair take?
A sensor replacement or coil clean usually takes one visit. Leak repairs take longer, since the technician must find the leak, repair it, pressure test, vacuum and recharge. Component replacements such as an expansion valve or strainer also involve refrigerant work. Where a part needs ordering, the technician makes the system safe and returns.
Is repair worthwhile on an older system?
Usually, if the compressor has not been damaged. Leak repairs, valve replacements and sensor fixes restore normal operation at a fraction of the cost of a new system. However, if the compressor has been overheating for a long time and now shows signs of wear, or if the coils are badly corroded, replacement may be better value. Our technician will explain both paths.
Can a multi split overheat?
Yes. Because a multi split carries a larger charge across several pipe runs, a leak in any run can starve the shared compressor. In addition, when several rooms call for cooling at once, the load is higher. The technician checks each run and each head during diagnosis, which takes a little longer but avoids missing a second leak elsewhere in the system.
Should you top up the gas yourself?
No. Handling refrigerant in Australia requires a licence, and R32 needs suitable equipment and safe procedures. Retail recharge kits can overcharge the system, introduce air and moisture, and mask the leak without fixing it. A licensed technician will find and repair the leak, then charge the system correctly by weight, which protects the compressor and restores proper performance for the long term.
When should you call us?
Call if six flashes return after one cool down restart, cooling has been weakening, frost appears on the pipes, or oily marks show at joints.
Who fixes this in Sydney?
Our technicians repair Hitachi outdoor units right across Greater Sydney. Ring 02 9071 1142 or book through our contact page.
Frequently asked questions
What does six flashes of the Hitachi operation lamp mean?
Hitachi service tables list an overheat thermistor temperature rise.
Is low gas a common cause?
Yes. Low refrigerant makes the compressor run hot.
Can the sensor be faulty?
Yes. The technician checks the real temperature before deciding.
How long should it cool before restarting?
At least ten minutes with power off at the switchboard.
Does it damage the compressor?
The stop protects it, but repeated overheating shortens its life.
How do I book?
Ring 02 9071 1142 or use our contact page.