Hitachi Air Conditioner Error Codes and Blinking Lamps
Hitachi air conditioner error codes on airHome wall splits are mostly told through blinking lamps rather than letters on a screen. When the indoor unit finds a fault on its own side, the timer lamp blinks a set number of times. When the outdoor unit has the problem, the operation lamp does the blinking instead. Counting those blinks tells you, and us, where to start looking.
How do Hitachi airHome units report a fault?
Hitachi service documentation for the airHome 400 and 600 ranges describes a simple split. Indoor faults make the orange timer lamp on the indoor unit blink, while outdoor faults make the operation lamp blink. The blinks repeat in groups, with a pause between each group, so you can count them.
Inside the outdoor unit, a board LED marked LD301 also blinks for some faults, though owners should never open the cabinet to look at it.
How should you count the blinks?
Stand where you can see the indoor display clearly and wait for a pause. Then count each flash until the next pause. Watch at least two full cycles to be sure, since it is easy to miss the first blink.
Filming the display on your phone and counting during playback works well for longer sequences.
Which Hitachi air conditioner error codes come from the indoor side?
The airHome service catalogue lists these timer lamp patterns.
- 1 blink, refrigerant cycle fault.
- 2 blinks, outdoor unit in forced operation.
- 3 blinks, indoor communication error.
- 9 blinks, indoor thermistor defect.
- 10 blinks, abnormal indoor DC fan motor rotation.
- 12 blinks, outdoor communication error.
- 13 blinks, EEPROM read error.
- 20 blinks, human sensor defect.
- 21 blinks, interface defect caused by another unit.
- 25 blinks, connector defect at CN7A or CN7B.
Each common pattern has its own detailed guide, linked further down this page.
Which codes come from the outdoor side?
Outdoor faults blink the operation lamp.
- 2 blinks, peak current cut.
- 3 blinks, compressor abnormal low speed rotation.
- 4 blinks, compressor switching failure.
- 5 blinks, overload lower limit cut.
- 6 blinks, overheat thermistor temperature rise.
- 7 blinks, abnormal outdoor thermistor.
- 9 blinks, communication error.
- 10 blinks, abnormal power source.
- 11 blinks, fan stop due to strong wind.
- 12 blinks, outdoor fan motor fault.
- 13 blinks, EEPROM read error.
- 14 blinks, DC voltage abnormal.
- 15 blinks, abnormal circuit board.
- 16 blinks, high load stop.
Where are the detailed guides for indoor codes?
Our indoor guides cover timer lamp 1 blink, 3 blinks, 9 blinks, 10 blinks, 12 blinks, 13 blinks and 20 blinks.
Where are the detailed guides for outdoor codes?
Our outdoor guides cover operation lamp 2 blinks, 3 blinks, 4 blinks, 5 blinks, 6 blinks, 7 blinks, 10 blinks, 12 blinks, 14 blinks and 16 blinks.
Is every blinking lamp a fault?
No. Several lamp patterns are normal. The operation lamp blinks during preheating and defrost in heating mode. The clean function lamp blinks when FrostWash cannot start or has not run for a long time. A wifi lamp blinking three times means the unit is in pairing mode.
Our lights flashing guide explains the normal patterns.
Can the unit tell you the code another way?
Yes. The service catalogue describes a buzzer function. Holding the up or down button on the handset for about five seconds makes the unit sound its buzzer in the same rhythm as the blinking lamp. That lets a technician hear the pattern over the phone.
A technician can also call up the stored error history through a handset button sequence, which shows the last five faults.
Can you reset a Hitachi fault yourself?
You can try one clean restart. Switch the system off at the switchboard, wait at least five minutes, then switch it back on. If the same pattern returns, the fault is real. Avoid repeated resets for compressor, current and voltage faults, since each restart adds stress.
Our reset guide explains the method.
Do older Hitachi models use the same codes?
Older Hitachi wall splits also used a blinking timer lamp, but the exact patterns can differ between generations. The list on this page comes from the airHome service catalogue. If your unit is older, or the pattern does not match, note it carefully and call us.
Do ducted Hitachi systems use the same patterns?
Ducted systems, such as the airCore 700, usually show codes on the wired controller rather than by blinking lamps. Our ducted page covers ducted systems.
What should you write down?
Note the lamp that blinks, the number of blinks, the indoor model number, the mode you were using, the weather and when the fault started. That information lets us plan the right tests and bring likely parts.
When should you call a technician?
Call us if a pattern returns after one reset, the breaker trips, you notice burning smells, water drips indoors or the outdoor unit makes grinding or banging noises.
Why does Hitachi use blinking lamps instead of letters?
Many airHome indoor units have a clean front with a few small indicator lamps rather than a large character display. As a result, Hitachi designed the self diagnosis around blink counts. The approach is simple and works even when the handset is lost. However, it does mean you need to count carefully, since a single missed blink changes the meaning.
What do the indoor faults have in common?
Broadly, indoor patterns point to the indoor board, its sensors, the indoor fan, memory or the link to the outdoor unit. For example, nine blinks relates to an indoor thermistor, while ten blinks relates to the indoor fan motor. Similarly, three and twelve blinks both concern communication between the units, from opposite ends of the link.
Therefore, an indoor pattern does not always mean the indoor unit is faulty. Communication faults in particular can start at the outdoor end or in the cable between.
What do the outdoor faults have in common?
Outdoor patterns usually involve the inverter drive, the compressor, outdoor sensors, the outdoor fan or the power supply. For instance, two blinks, peak current cut, means the drive saw a sudden surge of current. Meanwhile, five and sixteen blinks relate to heavy load conditions, often on very hot days. In addition, ten and fourteen blinks relate to the power supply and internal DC voltage.
Consequently, outdoor faults are often linked to heat, airflow, refrigerant charge or supply quality, as well as to failed parts.
Which codes are most common in Sydney?
In our experience across Sydney, summer brings the most outdoor faults, particularly overload, high load and overheat patterns when outdoor units bake in afternoon sun. Storms bring communication and power source patterns. Meanwhile, sensor and fan faults appear throughout the year as parts age.
How can you reduce fault codes?
First, keep the indoor filters clean so airflow stays healthy. Next, keep the outdoor unit clear of plants, bins and leaves. Then, book a yearly service so a technician can clean coils, tighten connections and check refrigerant pressures. Finally, avoid extreme set points on very hot or cold days.
Our service page explains what a service covers.
What happens if you ignore a pattern?
The unit usually stops or limits output when it detects a fault, so it is protecting itself. Restarting it over and over without fixing the cause can stress the compressor, the drive board or the fan. In addition, some faults, such as refrigerant cycle problems, get worse with time. Therefore, it pays to book a repair once a pattern repeats.
How does a technician use the code?
The pattern narrows the search to a small group of parts. For example, nine blinks leads the technician to test the indoor thermistors and their wiring, while twelve blinks on the operation lamp leads them to the outdoor fan motor and its drive. They then measure resistance, voltage, current and pressures to confirm the cause before replacing anything.
Our repair page explains how a visit runs.
What if two lamps blink at once?
Some situations show more than one lamp. For example, the clean function lamp may blink for FrostWash reasons while another lamp shows a fault. Note every lamp that blinks and how, then tell us. A short video is ideal.
Are codes stored after power is lost?
According to the service catalogue, the unit keeps an error history that a technician can view through a handset sequence. Even if the blinking stops after a power cut, the history may still show what happened. That is why it helps to tell us about any earlier patterns too.
Which Hitachi models do these codes apply to?
The patterns on this page come from the service catalogue for the airHome 400 and airHome 600 wall splits. Hitachi sells the airHome range in Australia through Temperzone, alongside the airHome 500 cooling only range and the E Series. Related models often share the same self diagnosis system, though details can vary. Our models page explains the ranges and how to find your model number.
How do you find the model number?
Look for the rating label on the side of the indoor unit. Australian airHome indoor units carry numbers such as RAK DJ60PHAT, while the matching outdoor unit starts with RAC. Give us the full number exactly as printed, since the letters at the end identify the range and generation.
What about the outdoor board LED?
Inside the outdoor unit, an LED on the main board, marked LD301 in the service catalogue, blinks for certain faults. Technicians read it during diagnosis with the right safety steps. Owners should not open the cabinet, since the board holds stored charge after power is removed.
Can the app show error codes?
Connected airHome models use the airCloud Go app. The wifi lamp on the indoor unit has its own patterns for router and cloud connection problems, which are separate from fault codes. Our wifi guide explains those patterns.
What if the pattern is not on this list?
Write down exactly what you see, including which lamp, how many blinks and how long the pauses are. Then call us. Some patterns belong to older generations or other product families, and our technicians can identify them on site.
How quickly should you act on a pattern?
Act straight away on any pattern linked to current, voltage or the compressor, such as two, three, four, ten or fourteen blinks on the operation lamp. Switch the system off at the switchboard and call us. For sensor, memory or communication patterns, one reset is reasonable, but book a check if the pattern returns. Meanwhile, keep notes of when it happens, since that history helps the technician find intermittent faults.
Does a fault code affect the warranty?
A fault code itself does not affect cover. Hitachi lists a six year parts and labour warranty on the airHome wall mounted range in Australia. Genuine part failures within that period may be covered, so keep your proof of purchase handy. Damage from storms, pests or poor installation may be treated differently.
Can we help over the phone first?
Often, yes. Tell our team which lamp is blinking and how many times, and we can usually explain what the pattern means, whether it is safe to try a reset and what the visit is likely to involve. If the unit supports it, we may ask you to turn on the buzzer pattern so we can hear it ourselves and plan the visit with more confidence.
Do we fix Hitachi faults across Sydney?
Yes. Our technicians repair Hitachi airHome wall splits and ducted systems throughout Greater Sydney, as our areas page shows.
Ring 02 9071 1142 or book through our contact page.
Frequently asked questions
Which lamp shows indoor faults?
The timer lamp blinks for indoor faults on airHome units.
Which lamp shows outdoor faults?
The operation lamp blinks for outdoor faults.
Is a blinking operation lamp in winter a fault?
Not always. It also blinks during preheating and defrost.
Can the unit sound the code?
Yes. Holding up or down for about five seconds turns on the buzzer pattern.
Should I keep resetting?
No. Try once, then call us if the pattern returns.
How do I book?
Call 02 9071 1142 or use our contact page.